The CKN Knowledge in Practice Centre is in the early stages of content creation and currently focuses on the theme of thermal management.
We appreciate any feedback or content suggestions/requests using the links below

Content requests General feedback Feedback on this page

  • Home
  • Introduction to Composites
    • Fundamentals of composite materials
      • How Composites Differ From Metals
      • When to Use Composites
      • Composites design
      • Composites manufacturing
    • Systems approach to composite materials
  • Foundational Knowledge
    • Materials science
      • Material structure
        • Polymer (matrix) structure
          • Thermoplastic polymers
          • Thermoset polymers
      • Material properties
        • Basic Definitions of Material Properties
          • Thermal conductivity
          • Specific heat capacity
          • Thermal diffusivity
        • Polymer properties
          • Heat of reaction
          • Degree of cure
          • Outgassing of Polymer Resins
          • Glass transition temperature (Tg)
          • Viscosity (resin)
        • Reinforcement properties
        • Composite properties
          • Fatigue Limits
          • Failure Theories
          • Safety Factors
          • Macro-Mechanics
          • Micro-Mechanics
    • Processing science
      • Thermal behaviour
        • Heat transfer
          • Conduction
          • Convection
        • Thermal phase transitions of polymers
        • Cure of thermosetting polymers
    • Foundational method documents
      • How to measure curing time and degree of cure
      • How to measure gel time
      • How to measure reinforcement content (and corresponding matrix content)
      • Tensile Testing
  • Systems Knowledge
    • System parameters - inputs and outcomes
    • System interactions
    • Thermal and cure/crystallization management (TM)
      • Effect of material in a thermal management system
      • Effect of shape in a thermal management system
      • Effect of tooling in a thermal management system
      • Effect of equipment in a thermal management system
    • Materials deposition and consolidation management (MDCM)
    • Residual stress and dimensional control management (RSDM)
      • Effect of material in a RSDM system
      • Effect of shape in a RSDM system
      • Effect of tooling in a RSDM system
      • Effect of equipment in a RSDM system
    • Machining and assembly management (MAM)
    • Quality/inspection management (QIM)
    • Systems knowledge method documents
      • How to perform an experimental thermal profile
  • Systems Catalogue
    • The factory
      • Factory layout (where)
      • Objects in the factory (what)
        • Material
          • Cores & inserts
            • Foam
            • Honeycomb
          • Matrix
            • Fire Retardant Resins/Additives
            • Epoxy resin
            • Polyester resin
          • Prepreg
        • Shape
        • Tooling and consumables
        • Equipment
          • Autoclave
          • Oven
          • Room temperature transformation
          • Hot press
      • Factory cells (where and how)
        • Testing
          • Thermomechanical Analyzer (TMA)
        • Material deposition
          • Automated fibre placement (AFP)
          • Compression moulding
          • Filament winding
          • Hand layup prepreg (Autoclave/Out-of-autoclave) processing
          • Vacuum assisted resin transfer moulding (VARTM)/resin infusion (VARI)
          • Wet layup
        • Thermal transformation
    • Resources
      • Composites Courses at Canadian HEI
  • Practice
    • Integrated Product Development
      • Practice for Developing a Product
        • Composite Production Part Drawing
        • Selecting Functional Requirements
        • Shape Development
        • Material Selection
        • Practice for Identifying Process Steps
      • Practice for Developing a Process Step
        • Practice for Developing a Deposition Step
          • Resin degassing
          • Practice for Developing a Wet Lay-up
        • Practice for Developing a Demoulding Step
        • Practice for Developing a Consolidation Step
          • Debulking
          • Vacuum Bagging
            • Vacuum Bagging for Vacuum Infusion
            • Vacuum Bagging for Prepregs
          • Consolidation of Thermoplastics
        • Practice for Developing a Receiving and Storage Step
        • Practice for developing a thermal transformation process step
          • Developing production scale tooling
      • Ensuring quality during curing of thick parts
      • Ensuring quality during production of variable thickness parts
      • Ensuring tooling choice meets part quality metrics
      • Maintaining equivalency during cure for different fibre architectures
    • Production Optimization
      • Process selection for production scale-up
      • Decreasing Cure Cycle Time
      • Increasing throughput by curing parts simultaneously
      • Maintaining quality when scaling-up from coupons to production-ready parts
      • Optimizing a cure cycle for improved production rates
      • Practice of Mould Maintenance
    • Production Troubleshooting
      • Practice for troubleshooting a Light RTM step
      • Troubleshooting scaling issues from small to large parts
      • Transitioning tooling styles between different thermal transformation equipment
      • Troubleshooting when changing production tooling material
      • Troubleshooting a cure cycle for improved production rates
      • Maintaining part quality when changing curing equipment
      • Troubleshooting part quality during cure when changing the reinforcement
      • Troubleshooting tooling to achieve part quality
      • Troubleshooting scale-up issues from thin to thick parts
      • Ensuring appropriate resin flow and part consolidation for a new cure cycle
      • Troubleshooting scaling-up issues from coupons to parts
      • Ensuring appropriate resin flow and part consolidation for a new material
      • Troubleshooting quality issues during cure for different equipment types
  • Case Studies
    • Development
      • Lack of Requirements in Product Development
      • Conducting a thermal tooling survey on three complex tools of different materials
      • Developing for Future Production Scale Up
      • Use of Right Sized Simulation to Aid Decision Making in Thermoplastic Composite Manufacturing Systems
      • Feasibility of Using Composite Materials in Mobile Food Truck Tandoor Ovens
      • Automotive Battery Enclosure Material and Manufacturing Assessment
      • Product Development Stage Gate Methodology for a Composite Shroud
      • Process Selection for a Composite Transit Vehicle Door
    • Optimization
      • Optimization of a hot press process for bike components
      • Optimizing Cost vs Weight for Low Production Volume Parts
      • Cost Comparison Study of a GFRP Leisure Boat Hull Manufacturing Method; Spray Up vs Resin Infusion
      • Using Barcol Hardness Measurements to Correlate Hardness and Degree of Cure
    • Troubleshooting
      • Troubleshooting of room temperature processes for large recreational and industrial parts
  • Perspectives
    • Presentations
      • Dr. Anoush Poursartip's cdmHUB global composites expert webinar
    • Interviews
      • Interview with Prof. Kevin Potter
    • AIM Events - Webinars
      • Introduction to quality assurance and quality control in composites
      • The Current State of Composite Materials in the Bicycle Industry
      • Advanced x-ray imaging of carbon fiber microstructure
      • Implementation of Bolted Joints in Composites
      • Filament Winding
      • Introduction to Bolted Joints in Composites
      • Introduction to Damage and Repair of Composite Sandwich Structures
      • Introduction to Non-Destructive Testing of Composite Materials
      • Introduction to Repair of Composite Structures
      • Viscoelasticity and Composite Materials
      • Introduction to Adhesive Bonding - Part II
      • Introduction to Adhesive Bonding - Part I
      • Sandwich Panels in Aerospace
      • Introduction to Tooling for Composite Materials Processing
      • An Introduction to Composites Sustainability
      • Porosity in Composite Materials - Part II
      • Porosity in Composite Materials - Part I
      • Pultrusion of Thermoplastic Composites
      • Simulation models for rapid liquid composite molding
      • CKN’s Approach to Developing Products with Composite Materials
      • Introduction to Sandwich Structures - Materials and Processing
      • Case Study: Optimizing a Press Moulding Process
      • Introduction to the welding of thermoplastic composites
      • Introduction to the processing of thermoplastic composites
      • Heat Transfer in Composites Processing
      • Effect of cure on mechanical properties of a composite (Part 2 of 2)
      • Effect of cure on mechanical properties of a composite (Part 1 of 2)
      • Fabric Forming: how it affects design and processing, and how simulation can address this
      • Fibre Architecture: Availability, pros and cons, and selection for my application
      • Strengthening the Canadian Advanced Manufacturing Innovation Ecosystem: What types of intellectual property matter, and to whom?
      • Understanding Polyester Resin Processing: The Effect of Ambient Temperature on the Final Part
      • Composites Process Simulation: A Review of the State of the Art for Product Development
      • Resin Behaviour During Processing: What are the key resin properties to consider when developing a manufacturing process?
      • The Composites Knowledge in Practice Centre – an open resource for composites manufacturing knowledge and best practices
      • Deconstructing composites ''processing'' - Why it seems so complex and how to think about it in a structured way
      • Parameters for Structural Analysis of Composites
      • Costing composite parts
      • Composite materials engineering webinar series
        • Composite materials engineering webinar session 1 - Introduction
        • Composite materials engineering webinar session 2 - Constituent Materials - Fiber
        • Composite materials engineering webinar session 3 - Constituent materials - Resin
        • Composite materials engineering webinar session 4 - Thermal management and resin cure
        • Composite materials engineering webinar session 5 - Manufacturing processes - Introduction
        • Composite materials engineering webinar session 6 - Manufacturing processes - Prepreg processing
        • Composite materials engineering webinar session 7 - Manufacturing processes - Liquid composite moulding
        • Composite materials engineering webinar session 8 - Mechanics of composites - Part 1: Lamina level
        • Composite materials engineering webinar session 9 - Mechanics of composites - Part 2: Laminate level
        • Composite materials engineering webinar session 10 - Failure of composites
        • Composite materials engineering webinar session 11 - Defects
        • Composite materials engineering webinar session 12 - Testing
    • Diversity & Inclusion Coffee Breaks
      • D&I with James Richards
      • D&I with Janice Barton
      • D&I featuring Kero Saleib
      • D&I featuring Rosemary Pham
      • D&I featuring Sampada Bodkhe
      • D&I featuring Isabelle Paris
      • D&I featuring Janic Lauzon
      • D&I featuring Anoush Poursartip
      • D&I featuring Courtney Mandock
  • Resin flow
    • Darcy's law
  • Laminate Plate Theory Calculator

Reference - A finite element/control volume approach to mold filling in anisotropic porous media

From CKN Knowledge in Practice Centre
Draft
Create review
Type Journal
Title A finite element/control volume approach to mold filling in anisotropic porous media
Abstract Mold filling in anisotropic porous media is the governing phenomena in a number of composite manufacturing processes, such as resin transfer molding (RTM) and structural reaction injection molding (SRIM). In this paper we present a numerical simulation to predict the flow of a viscous fluid through a fiber network. The simulation is based on the finite element/control volume method. It can predict the movement of a free surface flow front in a thin shell mold geometry of arbitrary shape and with varying thickness. The flow through the fiber network is modeled using Darcy's law. Different permeabilities may be specified in the principal directions of the preform. The simulation permits the permeabilities to vary in magnitude and direction throughout the medium. Experiments were carried out to measure the characteristic permeabilities of fiber preforms. The results of the simulation are compared with experiments performed in a flat rectangular mold using a Newtonian fluid. A variety of preforms and processing conditions were used to verify the numerical model. Copyright © 1990 Society of Plastics Engineers
Accessed 2025-01-14
Authors
  • Bruschke, M. V.
  • Advani, S. G.
Date 1990-12-1
Issue 6
Pages 398-405
Publisher John Wiley & Sons, Ltd
Journal Polymer Composites
Volume 11
Websites
DOI 10.1002/PC.750110613
ISSN 1548-0569
Cite
To cite this Reference:
  1. Edit any page with the VisualEditor.
  2. Position the cursor where the citation is needed.
  3. On the VE toolbar, click "Insert", then "Template".
  4. In the dialog form field, enter "Ref".
  5. Click "Add template".
  6. In the "Reference Page name" field, enter "C3d0093a-18e2-311e-a5d4-11e5bbde6ad4".
  7. (optional) Add a page number or range by clicking "Add more information".
  8. Click "Insert".

Engineered materials (designed to have specific properties) made from two or more constituent materials with different physical or chemical properties. The constituents remain separate and distinct on a macroscopic level within the finished structure.

For polymer matrix composites (PMCs), resin refers to the matrix; the continuous material phase that binds the reinforcement together, maintains shape, and transfers load. Resins are divided into two main groups: thermosets and thermoplastics.

Resin transfer moulding (RTM) involves loading a preform into a two (or more) piece, matched tool, closing it, and injecting resin under pressure (~15-100 psi, or ~1-7 bar).

Well suited to small to medium sized parts, limited to large sizes due to injection pressure loads and tool cost.

Flow front refers to the leading edge of the resin as it is flowing into and through the fibre preform.

‘Preform’ is the term for the fibre reinforcement. This is the stage between the raw material form after it is processed into an architecture (fabric, mat, etc.) and becoming a composite.

Retrieved from "https://compositeskn.org/KPC/index.php?title=Reference:C3d0093a-18e2-311e-a5d4-11e5bbde6ad4&oldid=6967"
CKN KPC logo

Welcome

Welcome to the CKN Knowledge in Practice Centre (KPC). The KPC is a resource for learning and applying scientific knowledge to the practice of composites manufacturing. As you navigate around the KPC, refer back to the information on this right-hand pane as a resource for understanding the intricacies of composites processing and why the KPC is laid out in the way that it is. The following video explains the KPC approach:

Understanding Composites Processing

The Knowledge in Practice Centre (KPC) is centered around a structured method of thinking about composite material manufacturing. From the top down, the heirarchy consists of:

The way that the material, shape, tooling & consumables and equipment (abbreviated as MSTE) interact with each other during a process step is critical to the outcome of the manufacturing step, and ultimately critical to the quality of the finished part. The interactions between MSTE during a process step can be numerous and complex, but the Knowledge in Practice Centre aims to make you aware of these interactions, understand how one parameter affects another, and understand how to analyze the problem using a systems based approach. Using this approach, the factory can then be developed with a complete understanding and control of all interactions.

The relationship between material, shape, tooling & consumables and equipment during a process step


Interrelationship of Function, Shape, Material & Process

Design for manufacturing is critical to ensuring the producibility of a part. Trouble arises when it is considered too late or not at all in the design process. Conversely, process design (controlling the interactions between shape, material, tooling & consumables and equipment to achieve a desired outcome) must always consider the shape and material of the part. Ashby has developed and popularized the approach linking design (function) to the choice of material and shape, which influence the process selected and vice versa, as shown below:

The relationship between function, material, shape and process


Within the Knowledge in Practice Centre the same methodology is applied but the process is more fully defined by also explicitly calling out the equipment and tooling & consumables. Note that in common usage, a process which consists of many steps can be arbitrarily defined by just one step, e.g. "spray-up". Though convenient, this can be misleading.

The relationship between function, material, shape and process consisting of Equipment and Tooling and consumables


Workflows

The KPC's Practice and Case Study volumes consist of three types of workflows:

  • Development - Analyzing the interactions between MSTE in the process steps to make decisions on processing parameters and understanding how the process steps and factory cells fit within the factory.
  • Troubleshooting - Guiding you to possible causes of processing issues affecting either cost, rate or quality and directing you to the most appropriate development workflow to improve the process
  • Optimization - An expansion on the development workflows where a larger number of options are considered to achieve the best mixture of cost, rate & quality for your application.

To use this website, you must agree to our Terms and Conditions and Privacy Policy.

By clicking "I Accept" below, you confirm that you have read, understood, and accepted our Terms and Conditions and Privacy Policy.

Powered by MediaWiki
Powered by Semantic MediaWiki